Skip to content

Global direct purchasing · Components, systems and technical resources

Your cart

Your cart is empty. Standard components are ordered straight from the catalogue, which is organised by what the part has to do inside a build.

Shop components
Checkout View cart
Shop Components

Marine Epoxy AB Potting Compound Kit

Price range: $25.99 through $26.99

Marine epoxy potting compound for cable, motor, and enclosure connections.

A:B 4:1 by weight;

Separate 500 g of Part A and 100 g of Part B into bottles.

Technical Downloads Request a document

Description

Illustrative two-bottle marine epoxy kit beside a cable-entry enclosure
Marine sealing and potting

Seal critical connections with a two-part epoxy.

This flowable A/B epoxy is supplied for potting and sealing work around motors, cable connections and enclosure interfaces. It is applied as a liquid and develops its protective properties after a full cure.

4:1A:B mixing ratio by weight
24 hFull cure at 25 °C
A + BSeparate bottles
Product introduction

Made for marine equipment potting.

The supplier describes this customized epoxy as more flowable and resistant to heat and corrosion than its standard formulation. It is used around motor seals, wire joints and the internal or external sealing points of enclosures. Viscosity before cure depends on formulation and process.

Once fully cured, the supplier lists moisture and dust protection, electrical insulation, heat transfer, sealing and vibration protection among its functions. The finished assembly must be checked for its actual seawater exposure, pressure and operating conditions.

Application fit

A measured process for reliable potting.

01

Motor interfaces

Encapsulate prepared electrical and sealing transitions in a suitable motor assembly.

02

Cable connections

Pot wire joints and cable exits after the conductors are positioned and the cavity is clean.

03

Enclosure sealing points

Fill suitable penetrations or interfaces on the inside or outside of an enclosure.

04

Control air bubbles

Use a careful pour or suitable vacuum process to reduce voids before the material cures.

Specifications

Check the mixing and cure data.

A:B mixing ratio 4:1 by weight
Weighing accuracy Within 0.1 g (supplier instruction)
Mixing time About 1 minute
Surface dry at 25 °C Approximately 6–8 hours
Full cure at 25 °C Approximately 24 hours
Heat-cure option 60 °C for 2 hours (supplier stated)
Maximum hardness After 3 days (supplier stated)

Temperature matters. Cure is generally faster in warmer conditions and slower in cooler conditions. Use the 60 °C option only when all components in the assembly tolerate that temperature. These times are supplier guidance; no finished-assembly depth or pressure rating is specified.

Application guide

Prepare, weigh, fill, cure.

01

Prepare

Use a clean, dry container. Tare the scale and shake or stir both bottles to disperse any settled material.

02

Weigh and mix

Measure A:B strictly at 4:1 by weight. Add A first, then B, and stir thoroughly for about one minute. Close both bottles after use.

03

Fill the cavity

Keep the syringe tip below the resin surface when drawing material to avoid air intake. Dispense into the prepared area; vacuum degassing may be used when appropriate.

04

Allow to cure

Keep dust and strong light away. Check the surface during the first hour and remove visible bubbles. Allow approximately 24 hours at 25 °C for full cure.

Package contents

Included in the package.

Marine epoxy AB potting kit

  • Part A epoxy resin bottle · 500 g1
  • Part B curing agent bottle · 100 g1
Illustrative layout of one larger Part A bottle and one smaller Part B bottle

Additional information

Options

With 10pcs Wipes, Without Wipes

Buying this part in quantity, or in a changed form

The store price covers single units and small quantities. Larger quantities, changes to the standard part and systems that have to be checked are handled case by case.

Not certain it fits?

Send the part number and the system it goes into.

Depth, voltage, thrust, interface and the surrounding parts are enough for us to tell you whether this product fits, what it needs to run, and what to watch for during integration.