Skip to content

Global direct purchasing · Components, systems and technical resources

Your cart

Your cart is empty. Standard components are ordered straight from the catalogue, which is organised by what the part has to do inside a build.

Shop components
Checkout View cart
Shop Components

8–26 mm Cable Splice Junction Box Mold Kit

$9.99

A semi-transparent two-part mold for vulcanized or resin-potted inline cable joints. Fits cable outside diameters of 8–26 mm. Two vent openings help release trapped air, and the stepped exits can be adjusted to the cable.

Mold dimensions: 185 × 40 × 45 mm. Reference fill amount: about 150 g.

The kit includes one mold set, one insulation tape roll, and one cotton strip set.

Technical Downloads Request a document

Description

Two halves and filling-port cap of the translucent 8–26 mm inline cable splice mold
8–26 mm cable splice mold

Give a larger cable joint a defined shape.

A semi-transparent two-part mold for straight-through cable splices. Its snap-fit halves, tapered cable exits, filling port and two air-release openings support a controlled vulcanizing or resin-potting process.

8–26 mmApplicable cable OD
185 × 40 × 45 mmMold dimensions
≈150 gReference fill amount
Product introduction

Encapsulate the connection in a split shell.

Use the mold to form a vulcanized or resin-potted inline cable joint. The semi-transparent shell lets the operator check the fill, while two air-release openings help reduce trapped bubbles. The matching halves clip together and can be separated for demolding after the chosen compound has cured.

With compatible materials and a properly completed process, the encapsulated connection is intended to isolate the cable joint from water and air. The supplier describes use in underwater cable joining; qualify the finished joint for its intended depth, pressure and service conditions.

Mold design

Designed around filling and fit.

01

See the fill

The semi-transparent body helps you monitor the compound during application.

02

Vent trapped air

Two openings provide an escape route for air as the cavity fills.

03

Adjust cable exits

Stepped end grooves can be trimmed to fit the cable diameter, following the assembly procedure.

04

Open the two halves

Snap-together construction makes the shell convenient to assemble and remove after curing.

Specifications

Check the cable and mold dimensions.

Applicable cable outside diameter 8–26 mm
Mold dimensions 185 × 40 × 45 mm
Reference filling amount Approximately 150 g
Cable application Low-voltage power cable up to 1 kV; communications and signal cable
Supplier example: unarmored 3 × 10.4 × 16 mm²
Supplier example: armored 3 × 10.4 × 10 mm²
Shell design Semi-transparent, two-piece snap fit; two vent openings
Opened 8–26 mm cable splice mold showing tapered exits and oval filling port
Applications

For power and signal cable joints.

Supplier examples include power, communications and signal lines in municipal works, water projects, landscape and street lighting, and tunnels. Match the actual cable outside diameter and joint build-up to the cavity. The conductor sizes in the supplier chart are examples, not a substitute for checking cable OD.

The approximately 150 g fill amount is a planning reference. Actual consumption, working time, curing time and the finished seal depend on the cable, compound and installation method. No numerical depth, pressure or IP rating is supplied for the mold itself.

Package contents

Included in the kit.

8–26 mm splice mold kit

  • Mold set 1
  • Insulation tape roll 1
  • Cotton strip set 1
FAQ

Common questions

Is 185 × 40 × 45 mm the finished joint size?

No. It is the stated product size of the mold. The final joint depends on the cavity and the completed cable assembly.

Can the mold be used for underwater joints?

The supplier describes underwater cable splicing with a suitable compound. The completed joint must be tested for its intended service conditions.

How much compound is needed?

The supplier gives approximately 150 g as a reference. Confirm the amount for the actual cable and joint design.

Buying this part in quantity, or in a changed form

The store price covers single units and small quantities. Larger quantities, changes to the standard part and systems that have to be checked are handled case by case.

Not certain it fits?

Send the part number and the system it goes into.

Depth, voltage, thrust, interface and the surrounding parts are enough for us to tell you whether this product fits, what it needs to run, and what to watch for during integration.